<DIV style="font-family:Arial, sans-serif; font-size:10pt;"><DIV>Alan,  If you're just using aluminum it might be worth it to just start over.  Make sure your tool is centered ,  try practicing on a another part you don't care about, If you change your angle of attack and run at a very high speed ( I don't think you can go too fast with aluminum), also use coolant.   Your O ring groove should be perfectly smooth just using the tool.   Could be the rake is not right for what you're trying to do.</DIV><DIV> </DIV><DIV>Brian</DIV><DIV> </DIV><DIV><BR><BR>--- personal_submersibles@psubs.org wrote:<BR><BR>From: Alan via Personal_Submersibles <personal_submersibles@psubs.org><BR>To: Personal Submersibles General Discussion <personal_submersibles@psubs.org><BR>Subject: Re: [PSUBS-MAILIST] Finishing O-ring groove<BR>Date: Sat, 9 Sep 2017 13:16:24 +1200<BR><BR></DIV><DIV>Thanks Hugh, it's ID groove.</DIV><DIV>I have been cleaning up my OD grooves with sand paper, taking the</DIV><DIV>sharp edge off the groove then finishing with 1200 grit to get a polished </DIV><DIV>surface. Not sure if this is the done thing! The OD grooves had less chatter.</DIV><DIV>I have been setting the tool height to my dead centre in the tail stock; but</DIV><DIV>might put a centre in the chuck to double check. Will have a look at moving</DIV><DIV>the tool back as far as I can in the tool holder. </DIV><DIV>Any recommendations on a good anodiser? I did talk briefly to one who said</DIV><DIV>I didn't necessarily need to have a hard anodising finish for  a marine </DIV><DIV>application. Only if it might be knocked around! I have 5 lights each in 3 </DIV><DIV>sections, any idea of a ball park figure for what 15 pieces should cost me?</DIV><DIV>Cheers Alan</DIV><DIV><BR></DIV><DIV><BR><DIV>Sent from my iPad</DIV></DIV><DIV><BR>On 9/09/2017, at 12:16 PM, Hugh Fulton via Personal_Submersibles <<A href="mailto:personal_submersibles@psubs.org">personal_submersibles@psubs.org</A>> wrote:<BR><BR></DIV><BLOCKQUOTE><DIV><DIV><P><SPAN style="color: rgb(31, 73, 125); font-family: "Calibri","sans-serif"; font-size: 11pt;">Alan,</SPAN></P></DIV><P><SPAN style="color: rgb(31, 73, 125); font-family: "Calibri","sans-serif"; font-size: 11pt;">Post a picture/photo of how you are machining and your setup and then we can solve it.  Tool height is critical as is tool and work rigidity.</SPAN></P></DIV><P><SPAN style="color: rgb(31, 73, 125); font-family: "Calibri","sans-serif"; font-size: 11pt;">You should not have chatter if you are machining correctly. Is it an ID groove or an OD groove?  Hugh</SPAN></P><P><SPAN style="color: rgb(31, 73, 125); font-family: "Calibri","sans-serif"; font-size: 11pt;"></SPAN> <DIV><DIV style="border-width: 1pt medium medium; border-style: solid none none; border-color: rgb(181, 196, 223) currentColor currentColor; padding: 3pt 0cm 0cm;"></DIV></DIV></P><P><B><SPAN lang="EN-US" style="font-family: "Tahoma","sans-serif"; font-size: 10pt;">From:</SPAN></B><SPAN lang="EN-US" style="font-family: "Tahoma","sans-serif"; font-size: 10pt;"> Personal_Submersibles [<A href="mailto:personal_submersibles-bounces@psubs.org">mailto:personal_submersibles-bounces@psubs.org</A>] <B>On Behalf Of </B>Alan via Personal_Submersibles<BR><B>Sent:</B> Saturday, 9 September 2017 9:58 AM<BR><B>To:</B> Personal Submersibles General Discussion<BR><B>Subject:</B> Re: [PSUBS-MAILIST] Finishing O-ring groove</SPAN></P><P> <DIV></DIV><DIV></DIV></P><P>Thanks Hank.<DIV></DIV><DIV></DIV></P><P>I couldn't get a file in to this internal groove & it may jam. <DIV></DIV><DIV></DIV></P><P>About 2 & 1/2" diameter.<DIV></DIV><DIV></DIV></P><P>Will try my wire idea. I get there eventually doing it by hand<DIV></DIV><DIV></DIV></P><P>& folded sandpaper, but I'm considering doing another bunch<DIV></DIV><DIV></DIV></P><P>after this 4 & trying to find a better way.<DIV></DIV><DIV></DIV></P><P>Alan<BR><BR>Sent from my iPad<DIV></DIV><DIV></DIV></P><P style="margin-bottom: 12pt;"><BR>On 9/09/2017, at 9:43 AM, hank pronk via Personal_Submersibles <<A href="mailto:personal_submersibles@psubs.org">personal_submersibles@psubs.org</A>> wrote:<DIV></DIV><BLOCKQUOTE style="margin-top: 5pt; margin-bottom: 5pt;"><DIV><DIV><DIV></DIV></DIV></DIV></BLOCKQUOTE></P><P><SPAN style="font-family: "Helvetica Neue"; font-size: 10pt;">Alan,</SPAN><DIV></DIV></P><P><SPAN style="font-family: "Helvetica Neue"; font-size: 10pt;">I use a flat file </SPAN><DIV></DIV></P><P><SPAN style="font-family: "Helvetica Neue"; font-size: 10pt;">Hank</SPAN><DIV></DIV></P><P><SPAN style="font-family: "Helvetica Neue"; font-size: 10pt;"></SPAN> <DIV><DIV><DIV></DIV></DIV></DIV></P><P><SPAN style="color: rgb(38, 40, 42); font-family: "Helvetica Neue"; font-size: 10pt;">On Friday, September 8, 2017, 3:21:54 PM MDT, Alan via Personal_Submersibles <<A href="mailto:personal_submersibles@psubs.org">personal_submersibles@psubs.org</A>> wrote: </SPAN><DIV></DIV></P><P><SPAN style="color: rgb(38, 40, 42); font-family: "Helvetica Neue"; font-size: 10pt;"></SPAN> <DIV></DIV></P><P><SPAN style="color: rgb(38, 40, 42); font-family: "Helvetica Neue"; font-size: 10pt;"></SPAN> <DIV><DIV></DIV></DIV></P><P><SPAN style="color: rgb(38, 40, 42); font-family: "Helvetica Neue"; font-size: 10pt;">Thanks, Brian & James.<BR>Unfortunately Brian I'm getting that little bit of chatter & I am<BR>needing to sand them down. Am also sanding the mating<BR>surfaces; finishing with 1200 grit & oil.<BR>I had thought of the dremel James. Trouble is that for these<BR>small grooves I would need the grinder on the dremel at the<BR>same profile as the O-ring groove. <BR>I might try bending up a peice of wire & hot glueing on <BR>sand paper. <BR>Not a lot I've found about this while Googling!<BR>Alan<BR><BR>Sent from my iPad<BR><BR>> On 9/09/2017, at 6:59 AM, Brian Cox via Personal_Submersibles <<A href="mailto:personal_submersibles@psubs.org">personal_submersibles@psubs.org</A>> wrote:<BR>> <BR>> Alan,  Aluminum likes high speed when turning the part, aside from just breaking the edges, you shouldn't need to use sand paper. <BR>> <BR>> Brian<BR>> <BR>> --- <A href="mailto:personal_submersibles@psubs.org">personal_submersibles@psubs.org</A> wrote:<BR>> <BR>> From: Alan via Personal_Submersibles <<A href="mailto:personal_submersibles@psubs.org">personal_submersibles@psubs.org</A>><BR>> To: <A href="mailto:personal_submersibles@psubs.org">personal_submersibles@psubs.org</A><BR>> Subject: [PSUBS-MAILIST] Finishing O-ring groove<BR>> Date: Fri, 8 Sep 2017 19:31:24 +1200<BR>> <BR>> I have been finishing some internal O-ring grooves in aluminium on the lathe, <BR>> with sandpaper.<BR>> The grooves are small; 3.4mm x 2mm. There was a bit of chatter after machining.<BR>> I am wondering if there is a better way to finish them rather than folding up small<BR>> bits of varying grades of sand paper & sticking my hand in the work. ( am being careful)<BR>> Maybe an abrasive paste & a bent piece of wire of a similar diameter to the groove?<BR>> The hole diameter is 60mm & the groove is only 4mm in from the face, but difficult<BR>> to get a straight stick with sandpaper in to it on the correct angle. I have a few to do.<BR>> Any suggestions thanks.<BR>> Alan<BR>> <BR>> Sent from my iPad<BR>> <BR>> _______________________________________________<BR>> Personal_Submersibles mailing list<BR>> <A href="mailto:Personal_Submersibles@psubs.org">Personal_Submersibles@psubs.org</A><BR>> <A href="http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles">http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles</A></SPAN><DIV></DIV></P><P><SPAN style="color: rgb(38, 40, 42); font-family: "Helvetica Neue"; font-size: 10pt;"><BR>> <BR>> <BR>> _______________________________________________<BR>> Personal_Submersibles mailing list<BR>> <A href="mailto:Personal_Submersibles@psubs.org">Personal_Submersibles@psubs.org</A><BR>> <A href="http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles">http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles</A><BR><BR><BR>_______________________________________________<BR>Personal_Submersibles mailing list<BR><A href="mailto:Personal_Submersibles@psubs.org">Personal_Submersibles@psubs.org</A><BR><A href="http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles">http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles</A></SPAN></P></BLOCKQUOTE><BLOCKQUOTE style="margin-top: 5pt; margin-bottom: 5pt;"><DIV><P>_______________________________________________<BR>Personal_Submersibles mailing list<BR><A href="mailto:Personal_Submersibles@psubs.org">Personal_Submersibles@psubs.org</A><BR><A href="http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles">http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles</A></P></DIV><DIV></DIV></BLOCKQUOTE></DIV><BLOCKQUOTE><DIV><SPAN>_______________________________________________</SPAN><BR><SPAN>Personal_Submersibles mailing list</SPAN><BR><SPAN><A href="mailto:Personal_Submersibles@psubs.org">Personal_Submersibles@psubs.org</A></SPAN><BR><SPAN><A href="http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles">http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles</A></SPAN><BR></DIV></BLOCKQUOTE>_______________________________________________
Personal_Submersibles mailing list
<A href="/eonapps/ft/wm/page/compose?send_to=Personal_Submersibles%40psubs.org">Personal_Submersibles@psubs.org</A>
<A href="http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles">http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles</A>