<DIV style="font-family:Arial, sans-serif; font-size:10pt;"><DIV>Alan,     My bearing and shaft are  basically locked in place by snap rings with equal resisting pressure either way the prop is turning. </DIV><DIV> </DIV><DIV>Brian<BR><BR>--- personal_submersibles@psubs.org wrote:<BR><BR>From: Alan via Personal_Submersibles <personal_submersibles@psubs.org><BR>To: Personal Submersibles General Discussion <personal_submersibles@psubs.org><BR>Subject: Re: [PSUBS-MAILIST] Motor Pod<BR>Date: Sun, 9 Apr 2017 14:15:17 +1200<BR><BR></DIV><DIV>Hi Brian,</DIV><DIV>you have me puzzled; I know you are a diver, so you realise that a </DIV><DIV>lot of the time your visibility will be no better than the length of your</DIV><DIV>sub. If the sphere is aft you will hit things before you see them.</DIV><DIV>If you are aft on the surface  & change to fore under the water I</DIV><DIV>would just be aware of whether your bearing set up is designed to</DIV><DIV>take axial pressure in both directions the same.</DIV><DIV>Alan</DIV><DIV><BR><BR><DIV>Sent from my iPad</DIV></DIV><DIV><BR>On 9/04/2017, at 8:41 AM, Brian Cox via Personal_Submersibles <<A href="mailto:personal_submersibles@psubs.org">personal_submersibles@psubs.org</A>> wrote:<BR><BR></DIV><BLOCKQUOTE><DIV><DIV style="font-family: Arial, sans-serif; font-size: 10pt;"><DIV>Alan,   The pods will turn,  I have it in various positions in different pictures.  They basically hang from that top disk and then they will both turn using a cable control.  The motors are only three HP, but I believe I can upgrade to 8 HP .  Yes, the sphere is aft.  </DIV><DIV> </DIV><DIV>Brian<BR><BR>--- <A href="mailto:personal_submersibles@psubs.org">personal_submersibles@psubs.org</A> wrote:<BR><BR>From: Alan via Personal_Submersibles <<A href="mailto:personal_submersibles@psubs.org">personal_submersibles@psubs.org</A>><BR>To: Personal Submersibles General Discussion <<A href="mailto:personal_submersibles@psubs.org">personal_submersibles@psubs.org</A>><BR>Subject: Re: [PSUBS-MAILIST] Motor Pod<BR>Date: Sun, 9 Apr 2017 07:57:02 +1200<BR><BR></DIV><DIV>Well done Brian.</DIV><DIV>I am just wondering about the orientation.</DIV><DIV>You say it is the port thruster. Are you driving the boat with the occupant sphere</DIV><DIV>at the rear? Also the vectoring of them, Is that permanent or just for the photo?</DIV><DIV>While I'm at it, what sort of horsepower are they.</DIV><DIV>Cheers Alan</DIV><DIV><BR><BR><DIV>Sent from my iPad</DIV></DIV><DIV><BR>On 9/04/2017, at 6:48 AM, Brian Cox via Personal_Submersibles <<A href="mailto:personal_submersibles@psubs.org">personal_submersibles@psubs.org</A>> wrote:<BR><BR></DIV><BLOCKQUOTE><DIV><DIV style="font-family: Arial, sans-serif; font-size: 10pt;"><DIV>Hi Everybody,</DIV><DIV>                            I finished my Port side motor pod.  Did a pressure test up to 10psi ,  still waiting on the silicone oil .  But it ran really smooth, had a bit of trouble when I machined the end caps, they weren't totally perfect, think I'll have the machine shop make a stab at it .  There were difficult to line up in my lathe and they were literally at the very maximum size my lathe could do.  But all my snap rings and o rings and epoxy thru hulls are good to go !</DIV><DIV> </DIV><DIV>Pics:</DIV></DIV></DIV></BLOCKQUOTE><BLOCKQUOTE><DIV><Pod1.jpg></DIV></BLOCKQUOTE><BLOCKQUOTE><DIV><Pod2.jpg></DIV></BLOCKQUOTE><BLOCKQUOTE><DIV><Pod3.jpg></DIV></BLOCKQUOTE><BLOCKQUOTE><DIV><Pod4.jpg></DIV></BLOCKQUOTE><BLOCKQUOTE><DIV><Pod5.jpg></DIV></BLOCKQUOTE><BLOCKQUOTE><DIV><SPAN>_______________________________________________</SPAN><BR><SPAN>Personal_Submersibles mailing list</SPAN><BR><SPAN><A href="mailto:Personal_Submersibles@psubs.org">Personal_Submersibles@psubs.org</A></SPAN><BR><SPAN><A href="http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles">http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles</A></SPAN><BR></DIV></BLOCKQUOTE>_______________________________________________
Personal_Submersibles mailing list
<A>Personal_Submersibles@psubs.org</A>
<A href="http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles">http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles</A>
</DIV></DIV></BLOCKQUOTE><BLOCKQUOTE><DIV><SPAN>_______________________________________________</SPAN><BR><SPAN>Personal_Submersibles mailing list</SPAN><BR><SPAN><A href="mailto:Personal_Submersibles@psubs.org">Personal_Submersibles@psubs.org</A></SPAN><BR><SPAN><A href="http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles">http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles</A></SPAN><BR></DIV></BLOCKQUOTE>_______________________________________________
Personal_Submersibles mailing list
<A href="/eonapps/ft/wm/page/compose?send_to=Personal_Submersibles%40psubs.org">Personal_Submersibles@psubs.org</A>
<A href="http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles">http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles</A>
</DIV>