<DIV style="font-family:Arial, sans-serif; font-size:10pt;"><DIV>Alan, Alec,    My batteries are inside, this would be power going to the motor.   It would be fused before going to the motors.  Is the individual penetrators only for a exterior battery pod?</DIV><DIV> </DIV><DIV>Brian<BR><BR>--- personal_submersibles@psubs.org wrote:<BR><BR>From: Alan James via Personal_Submersibles <personal_submersibles@psubs.org><BR>To: Personal Submersibles General Discussion <personal_submersibles@psubs.org><BR>Subject: Re: [PSUBS-MAILIST] penetrator<BR>Date: Sat, 17 Dec 2016 05:13:31 +0000 (UTC)<BR><BR></DIV><DIV style="color: rgb(0, 0, 0); font-family: HelveticaNeue, Helvetica Neue, Helvetica, Arial, Lucida Grande, sans-serif; font-size: 16px; background-color: rgb(255, 255, 255);"><DIV><SPAN></SPAN></DIV><DIV>Brian, Alec,</DIV><DIV>from memory GL says that the battery + & - should go through</DIV><DIV dir="ltr">separate penetrators but doesn't stipulate this for anything else.</DIV><DIV dir="ltr">This makes sense, because if there was a short, & unless there was a fuse in the</DIV><DIV dir="ltr">battery pod, then you could have a battery melt down.</DIV><DIV dir="ltr">Alan</DIV><DIV dir="ltr"><BR><BR></DIV><DIV style="display: block;">  <DIV style="font-family: HelveticaNeue, Helvetica Neue, Helvetica, Arial, Lucida Grande, sans-serif; font-size: 16px;"> <DIV style="font-family: HelveticaNeue, Helvetica Neue, Helvetica, Arial, Lucida Grande, sans-serif; font-size: 16px;"> <DIV dir="ltr"> <FONT face="Arial" size="2"> <HR size="1"> <B><SPAN style="font-weight: bold;">From:</SPAN></B> Alec Smyth via Personal_Submersibles <personal_submersibles@psubs.org><BR> <B><SPAN style="font-weight: bold;">To:</SPAN></B> Personal Submersibles General Discussion <personal_submersibles@psubs.org> <BR> <B><SPAN style="font-weight: bold;">Sent:</SPAN></B> Saturday, December 17, 2016 4:02 PM<BR> <B><SPAN style="font-weight: bold;">Subject:</SPAN></B> Re: [PSUBS-MAILIST] penetrator<BR> </FONT> </DIV> <DIV><BR><DIV><DIV><DIV dir="ltr">Hi Brian,<DIV><BR></DIV><DIV>If these are power penetrators and memory serves, ABS stipulates that each pole should go through a separate penetrator rather than separate conductors within the same one.</DIV><DIV><BR></DIV><DIV><BR></DIV><DIV>Best,</DIV><DIV><BR>Alec</DIV></DIV><DIV><BR><DIV>On Fri, Dec 16, 2016 at 7:49 PM, Brian Cox via Personal_Submersibles <SPAN dir="ltr"><<A href="mailto:personal_submersibles@psubs.org">personal_submersibles@psubs.org</A>></SPAN> wrote:<BR><BLOCKQUOTE style="margin: 0px 0px 0px 0.8ex; padding-left: 1ex; border-left-color: rgb(204, 204, 204); border-left-width: 1px; border-left-style: solid;"><DIV><DIV style="font-family: Arial, sans-serif; font-size: 10pt;"><DIV>Hank,   Starting to work on my electrical penetrators for my motor pods .   I need to run 4  - 1/4"  copper threaded rods thru a penetrator  what kind of separation between them is adequate ?  or should I break it up into two penetrators?</DIV><DIV> </DIV><DIV>Brian <BR><BR>--- <A href="mailto:personal_submersibles@psubs.org">personal_submersibles@psubs. org</A> wrote:<BR><BR>From: hank pronk via Personal_Submersibles <<A href="mailto:personal_submersibles@psubs.org">personal_submersibles@psubs. org</A>><BR>To: Personal Submersibles General Discussion <<A href="mailto:personal_submersibles@psubs.org">personal_submersibles@psubs. org</A>><BR>Subject: [PSUBS-MAILIST] penetrator<BR>Date: Fri, 16 Dec 2016 23:01:23 +0000 (UTC)<BR><BR></DIV><SPAN></SPAN><DIV style="color: rgb(0, 0, 0); font-family: HelveticaNeue, Helvetica Neue, Helvetica, Arial, Lucida Grande, sans-serif; font-size: 12px; background-color: rgb(255, 255, 255);"><DIV>Hi All,</DIV><DIV dir="ltr">I am looking for a penetrator supplier,  I am hoping to find male ends for some penetrators I have.</DIV><DIV dir="ltr"><BR></DIV><DIV dir="ltr"><BR></DIV><DIV>Hank</DIV></DIV>______________________________ _________________
Personal_Submersibles mailing list
<A>Personal_Submersibles@psubs. org</A>
<A href="http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles">http://www.psubs.org/mailman/ listinfo.cgi/personal_ submersibles</A>
</DIV></DIV><BR>______________________________ _________________<BR>
Personal_Submersibles mailing list<BR>
<A href="mailto:Personal_Submersibles@psubs.org">Personal_Submersibles@psubs. org</A><BR>
<A href="http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles">http://www.psubs.org/mailman/ listinfo.cgi/personal_ submersibles</A><BR>
<BR></BLOCKQUOTE></DIV><BR></DIV></DIV></DIV><BR><DIV>_______________________________________________<BR>Personal_Submersibles mailing list<BR><A href="mailto:Personal_Submersibles@psubs.org">Personal_Submersibles@psubs.org</A><BR><A href="http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles">http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles</A><BR></DIV><BR><BR></DIV> </DIV> </DIV>  </DIV></DIV>_______________________________________________
Personal_Submersibles mailing list
<A href="/eonapps/ft/wm/page/compose?send_to=Personal_Submersibles%40psubs.org">Personal_Submersibles@psubs.org</A>
<A href="http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles">http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles</A>
</DIV>