<DIV style="font-family:Arial, sans-serif; font-size:10pt;"><DIV>Good points Steve, Thanks!</DIV><DIV> </DIV><DIV>Brian Cox<BR><BR>--- personal_submersibles@psubs.org wrote:<BR><BR>From: Stephen Fordyce via Personal_Submersibles <personal_submersibles@psubs.org><BR>To: Personal Submersibles General Discussion <personal_submersibles@psubs.org><BR>Subject: Re: [PSUBS-MAILIST] Gauges and vacuum<BR>Date: Mon, 25 Jan 2016 17:35:21 +1100<BR><BR></DIV><DIV dir="ltr"><DIV>Hi Brian,</DIV><DIV>I recently went through an evaluation of some gauges I got - it was rather fun destroying them and a photo of the ruined internals is here:<BR></DIV><DIV><A href="https://www.facebook.com/tfmengineeringaust/photos/pcb.777589079041244/777589062374579/?type=3&theater">https://www.facebook.com/tfmengineeringaust/photos/pcb.777589079041244/777589062374579/?type=3&theatre</A><BR></DIV><DIV><BR></DIV><DIV>The bourdon tube flexes slightly with pressure and drives a rack and pinion mechanism that turns the needle.</DIV><DIV><BR></DIV><DIV>From a pressure perspective nothing catastrophically dangerous should happen (although make sure the case of any gauges can equalise with vacuum around it) but if you have a vacuum in the process bit of the gauge and 1atm in the case, the needle will try to go below the zero reading point and possibly mess up the zero point because the needle will be pushed against the zero point stopper quite hard.</DIV><DIV><BR></DIV><DIV>Easy ways to prevent this could include:</DIV><DIV>1. Make sure the pressure in the process connection and the case of the gauge are the same (ie. open the case and the process connection so they both see vacuum)</DIV><DIV>2. Keep the pressure in the process connection above the case pressure (ie. by locking some gas in or keeping open to 1atm outside the sub while you pull vacuum on it)</DIV><DIV><BR></DIV><DIV>Cheers,</DIV><DIV>Steve</DIV></DIV><DIV><BR><DIV>On Mon, Jan 25, 2016 at 4:59 PM, Brian Cox via Personal_Submersibles <SPAN dir="ltr"><<A href="mailto:personal_submersibles@psubs.org">personal_submersibles@psubs.org</A>></SPAN> wrote:<BR><BLOCKQUOTE style="margin: 0px 0px 0px 0.8ex; padding-left: 1ex; border-left-color: rgb(204, 204, 204); border-left-width: 1px; border-left-style: solid;"><DIV style="font-family: Arial,sans-serif; font-size: 10pt;"><DIV>Would anyone know if having a pressure gauge or a sea-water depth gauge in a vacuum environment could adversely affect the gauge?   Since I'm not to savy with the internal workings of analog pressure gauges I thought I might ask the group.  I'm about to pull a vacuum on my pressure hull and the thought occurred to me.</DIV><SPAN><FONT color="#888888"><DIV> </DIV><DIV>Brian Cox</DIV><DIV> </DIV></FONT></SPAN></DIV>
<BR>_______________________________________________<BR>
Personal_Submersibles mailing list<BR>
<A href="mailto:Personal_Submersibles@psubs.org">Personal_Submersibles@psubs.org</A><BR>
<A href="http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles">http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles</A><BR>
<BR></BLOCKQUOTE></DIV><BR></DIV>
_______________________________________________
Personal_Submersibles mailing list
<A href="/eonapps/ft/wm/page/compose?send_to=Personal_Submersibles%40psubs.org">Personal_Submersibles@psubs.org</A>
<A href="http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles">http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles</A>
</DIV>