<div dir="ltr">Thanks for the input guys.<div>Mine is a cylinder. <br></div><div><br></div><div>Problem is the rings are placed similar like the k-boats. If I place them at the excact place I would cut into them. And I can`t finish the weld on the tower-insert with the rings in place.</div><div>So maybe I can tack them in a little bit offset, cut the hole, tack in the tower-insert, remove the rings, finish welding the tower insert, then weld in the rings.</div><div>Does this sound like a good procedure?</div><div><br></div><div>Thanks,</div><div>André</div></div><div class="gmail_extra"><br><div class="gmail_quote">2015-05-09 3:49 GMT+02:00 hank pronk via Personal_Submersibles <span dir="ltr"><<a href="mailto:personal_submersibles@psubs.org" target="_blank">personal_submersibles@psubs.org</a>></span>:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><br>
Andre<br>
I would defiantly place the two rings in and I would put them exactly where they go and tack them.  There is a good chance that the opening will create a weak spot so to speak and the shell will bend up at the center of the hole.  Brian is right if it is a sphere, no worries.  The cylinder can go egg shape.<br>
Hank --------------------------------------------<br>
On Fri, 5/8/15, Brian Cox via Personal_Submersibles <<a href="mailto:personal_submersibles@psubs.org">personal_submersibles@psubs.org</a>> wrote:<br>
<br>
 Subject: Re: [PSUBS-MAILIST] Distortion when cutting in shell<br>
<span class=""> To: "Personal Submersibles General Discussion" <<a href="mailto:personal_submersibles@psubs.org">personal_submersibles@psubs.org</a>><br>
</span> Received: Friday, May 8, 2015, 7:05 PM<br>
<div><div class="h5"><br>
 That's 1/2"  if<br>
 it's A516 70 grade it should be no problem, <br>
  My Sphere thickness is 3/8" and<br>
 I could not detect any distortion.<br>
  Brian<br>
<br>
 --- <a href="mailto:personal_submersibles@psubs.org">personal_submersibles@psubs.org</a> wrote:<br>
<br>
 From: André Eriksen via<br>
 Personal_Submersibles<br>
 <<a href="mailto:personal_submersibles@psubs.org">personal_submersibles@psubs.org</a>><br>
 To:<br>
 Personal Submersibles General Discussion<br>
 <<a href="mailto:personal_submersibles@psubs.org">personal_submersibles@psubs.org</a>><br>
 Subject: [PSUBS-MAILIST] Distortion when<br>
 cutting in shell<br>
 Date: Fri, 8 May 2015<br>
 23:10:03 +0200<br>
<br>
 Hi all,<br>
 When you cut out the hole for the<br>
 conningtower, is distortion of the shell an<br>
 issue?<br>
 My shell is<br>
 12mm in thickness. Wondering if I should place a<br>
 reinforcement ring on either side of the hole to be cut -Not<br>
 welding them so I can remove them after I have tacked the<br>
 tower in place.<br>
<br>
<br>
 ThanksAndré<br>
 _______________________________________________<br>
 Personal_Submersibles mailing list<br>
 <a href="mailto:Personal_Submersibles@psubs.org">Personal_Submersibles@psubs.org</a><br>
 <a href="http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles" target="_blank">http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles</a><br>
<br>
<br>
</div></div> -----Inline Attachment Follows-----<br>
<div class="HOEnZb"><div class="h5"><br>
 _______________________________________________<br>
 Personal_Submersibles mailing list<br>
 <a href="mailto:Personal_Submersibles@psubs.org">Personal_Submersibles@psubs.org</a><br>
 <a href="http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles" target="_blank">http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles</a><br>
<br>
<br>
_______________________________________________<br>
Personal_Submersibles mailing list<br>
<a href="mailto:Personal_Submersibles@psubs.org">Personal_Submersibles@psubs.org</a><br>
<a href="http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles" target="_blank">http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles</a><br>
</div></div></blockquote></div><br><br clear="all"><div><br></div>-- <br><div class="gmail_signature"><div dir="ltr"><div><font face="arial black,sans-serif">Med Vennlig Hilsen / Regards</font></div><div><font face="arial black,sans-serif"><em>André Eriksen</em></font></div></div></div>
</div>