<div dir="ltr"><div>Hi Pete,</div><div>Sorry for the delay, ive been away.</div><div> </div><div>The through hull for the vent valve I just reamed out once it was in.  It didn't need any polishing to make the bar fit.   Probably because the hole is smaller than the others and so there wasn't as much distortion.  So those two were a lot easier.</div><div>Regards</div><div>James</div></div><div class="gmail_extra"><br><div class="gmail_quote">On 9 October 2014 22:06, Pete Niedermayr via Personal_Submersibles <span dir="ltr"><<a href="mailto:personal_submersibles@psubs.org" target="_blank">personal_submersibles@psubs.org</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><span><br>
Where the through hull for the vent valve welds into the conning tower<br>
<br>
</span><span>Pete<br>
<br>
--------------------------------------------<br>
On Thu, 10/9/14, James Frankland via Personal_Submersibles <<a href="mailto:personal_submersibles@psubs.org">personal_submersibles@psubs.org</a>> wrote:<br>
<br>
 Subject: Re: [PSUBS-MAILIST] Electrical thru-hull<br>
 To: "Personal Submersibles General Discussion" <<a href="mailto:personal_submersibles@psubs.org">personal_submersibles@psubs.org</a>><br>
</span> Date: Thursday, October 9, 2014, 6:02 AM<br>
<span><br>
 Hi<br>
 Pete, Not sure which one you mean? <br>
 Where the vent pipe attaches to the MBT?<br>
</span> orWhere the through hull for the<br>
<span> vent valve welds into the conning<br>
</span> tower?orsomething else?<br>
<div class="HOEnZb"><div class="h5"> James<br>
 On 9 October 2014 11:30,<br>
 Pete Niedermayr via Personal_Submersibles <<a href="mailto:personal_submersibles@psubs.org">personal_submersibles@psubs.org</a>><br>
 wrote:<br>
 James,<br>
 Was it the same for the MBT thru-hull ?<br>
<br>
<br>
<br>
 Pete<br>
<br>
<br>
<br>
 --------------------------------------------<br>
<br>
 On Thu, 10/9/14, James Frankland via Personal_Submersibles<br>
 <<a href="mailto:personal_submersibles@psubs.org">personal_submersibles@psubs.org</a>><br>
 wrote:<br>
<br>
<br>
<br>
  Subject: Re: [PSUBS-MAILIST] Electrical thru-hull<br>
<br>
  To: "Personal Submersibles General Discussion"<br>
 <<a href="mailto:personal_submersibles@psubs.org">personal_submersibles@psubs.org</a>><br>
<br>
  Date: Thursday, October 9, 2014, 4:50 AM<br>
<br>
<br>
<br>
  Hi<br>
<br>
  Bob,I had exactly the same problems.  As others<br>
<br>
  have said, forget the<br>
 honing tool.    I used the<br>
<br>
  appropriate sized hand reamer.  (A normal one, not an<br>
<br>
  adjustable which are a bit of a pain to use).  I ran<br>
 the<br>
<br>
  reamer through and then I used a bar with a slot cut in<br>
 it<br>
<br>
  and a piece of very fine emery paper (wet) through the<br>
 slot<br>
<br>
  to take off the smallest amounts until the fitting went<br>
<br>
  through.  Worked fine. Have a<br>
<br>
  picture here.  <a href="http://www.guernseysubmarine.com/Extended_files/Page23356.htmHope" target="_blank">http://www.guernseysubmarine.com/Extended_files/Page23356.htmHope</a><br>
<br>
  this helps, Good luckJames <br>
<br>
  -----Inline Attachment Follows-----<br>
<br>
<br>
<br>
  _______________________________________________<br>
<br>
  Personal_Submersibles mailing list<br>
<br>
  <a href="mailto:Personal_Submersibles@psubs.org">Personal_Submersibles@psubs.org</a><br>
<br>
  <a href="http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles" target="_blank">http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles</a><br>
<br>
<br>
<br>
<br>
<br>
 _______________________________________________<br>
<br>
 Personal_Submersibles mailing list<br>
<br>
 <a href="mailto:Personal_Submersibles@psubs.org">Personal_Submersibles@psubs.org</a><br>
<br>
 <a href="http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles" target="_blank">http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles</a><br>
<br>
<br>
<br>
 -----Inline Attachment Follows-----<br>
<br>
 _______________________________________________<br>
 Personal_Submersibles mailing list<br>
 <a href="mailto:Personal_Submersibles@psubs.org">Personal_Submersibles@psubs.org</a><br>
 <a href="http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles" target="_blank">http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles</a><br>
<br>
<br>
_______________________________________________<br>
Personal_Submersibles mailing list<br>
<a href="mailto:Personal_Submersibles@psubs.org">Personal_Submersibles@psubs.org</a><br>
<a href="http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles" target="_blank">http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles</a><br>
</div></div></blockquote></div><br></div>