<DIV style="font-family:Arial, sans-serif; font-size:10pt;"><DIV>The end cap will be cut out for a hatch, like Gamma is built, I like the curved look,  and I'll have a piece inserted for the land for the hatch..  The concern is the shrinkage when it's cooling .</DIV><DIV> </DIV><DIV>Brian <BR><BR>--- personal_submersibles@psubs.org wrote:<BR><BR>From: James Frankland via Personal_Submersibles <personal_submersibles@psubs.org><BR>To: Personal Submersibles General Discussion <personal_submersibles@psubs.org><BR>Subject: Re: [PSUBS-MAILIST] Conning tower<BR>Date: Tue, 23 Sep 2014 13:16:26 +0100<BR><BR></DIV><DIV dir="ltr"><DIV>Hi Brian,</DIV><DIV>Whats the end cap for on top?  Is that just to hold the shape while you weld?  Or is it permenant? </DIV><DIV> </DIV><DIV>When I did mine, which is about the same dimensions as yours, I made a circular disk from 6mm plate and welded it into the bottom of the tower.  Then I could roll it around for easier positions.  I cut the plate out later on.  I also made some flat disks from thick gauge steel and cramped them to each viewport, to soak up some of the heat.  Then I had loads of cups of tea in between runs.  No distortion.</DIV><DIV>Regards</DIV><DIV>James</DIV></DIV><DIV><BR><DIV>On 22 September 2014 06:55, Brian Cox via Personal_Submersibles <SPAN dir="ltr"><<A href="mailto:personal_submersibles@psubs.org">personal_submersibles@psubs.org</A>></SPAN> wrote:<BR><BLOCKQUOTE style="margin: 0px 0px 0px 0.8ex; padding-left: 1ex; border-left-color: rgb(204, 204, 204); border-left-width: 1px; border-left-style: solid;"><DIV style="font-family: Arial,sans-serif; font-size: 10pt;"><DIV>I'm having welding concerns when it comes to my conning tower.  I have an approximate 24" diameter conning tower by about 20" tall by 1/4" thick,  I want to put 8 viewports all the way around (6" disks with appropriate flanges) ,I'm planning on welding to the reinforcing ring on the bottom and an end cap on the top,  but even with those on there isn't the heat of welding all those flanges going to warp the crap out of the whole area ?   Can any welders weigh in on my concerns, Thanks.</DIV><SPAN><FONT color="#888888"><DIV> </DIV><DIV>Brian   </DIV></FONT></SPAN></DIV>
<BR>_______________________________________________<BR>
Personal_Submersibles mailing list<BR>
<A href="mailto:Personal_Submersibles@psubs.org">Personal_Submersibles@psubs.org</A><BR>
<A href="http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles">http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles</A><BR>
<BR></BLOCKQUOTE></DIV><BR></DIV>
_______________________________________________
Personal_Submersibles mailing list
<A href="/eonapps/ft/wm/page/compose?send_to=Personal_Submersibles%40psubs.org">Personal_Submersibles@psubs.org</A>
<A href="http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles">http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles</A>
</DIV>