[PSUBS-MAILIST] led

Rick Patton via Personal_Submersibles personal_submersibles at psubs.org
Fri Jan 1 15:26:54 EST 2021


Thanks Alan
I'll ask her if she is ok with that.

Rick

On Fri, Jan 1, 2021 at 10:17 AM Alan James via Personal_Submersibles <
personal_submersibles at psubs.org> wrote:

> Rick,
> Happy New Year.
> You have to have a Facebook account to click the join. You could join
> through your wife's account if you don't have one, but then she would get
> all the Psub fb news!
> Alan
>
> On Saturday, January 2, 2021, 07:17:32 AM GMT+13, Rick Patton via
> Personal_Submersibles <personal_submersibles at psubs.org> wrote:
>
>
> Alan
>
> yeah I hit the join tab on the link you gave me but nothing else happened
> so don't know what to expect or how it works. I just mounted the three
> motor controllers and cut the short small wires to the rheostats so I could
> extend them to the hand grips so I will be wiring them today.
> Happy New Year everyone! I made it til 11:00 PM which was better than I
> usually do.
>
> Rick
>
> On Thu, Dec 31, 2020 at 9:22 PM Alan James via Personal_Submersibles <
> personal_submersibles at psubs.org> wrote:
>
> Rick,
> Sounds good. You have got me thinking now about having a water sensing
> probe that triggers an alarm when the sub is out of the water and the
> lights are on.
> I would be quite capable of leaving them on & cooking them!
> I had a look on the Psubs fb page but couldn't see you on it yet. I think
> you have to be oked by the administration, so may be a delay.
> Alan
>
> On Thursday, December 31, 2020, 06:52:40 AM GMT+13, Rick Patton via
> Personal_Submersibles <personal_submersibles at psubs.org> wrote:
>
>
> Hi Alan
>
> I have a buck buster to lower the volts from 36 to 34 volt per it's
> requirement but don't plan on being able to dim them.
> I also have the toggle switches that illuminate when on so it will be
> easier to see what's on and what's off so hopefully they would never be on
> when sub is out of the water.
> I clicked the "join tab" but nothing happened as far as wanting me to come
> up with a password or anything so hopefully it worked.
>
> Rick
>
>
>
> On Tue, Dec 29, 2020 at 8:02 PM Alan James via Personal_Submersibles <
> personal_submersibles at psubs.org> wrote:
>
> Hi Rick,
> this link may work,
>
> https://www.facebook.com/groups/PSUBS/permalink/1342958449381043/
> Or your wife could search for Psubs on Facebook & join.
>
> Bottom of this thread is a diagram of the difference between a flip chip
> and normal cob. The flip chip throws more heat out the back. Google flip
> chip led for some good articles.
> I think I have destroyed a few flip chips mucking around with them, but
> haven't destroyed any mounted in my lights. They have had a thrashing as I
> have been using the lights in air & getting them really hot.
> (if water sizzles on them they are too hot)
> I wouldn't use marvel mystery oil in the housings because of the heat
> factor. If you accidentally left them on out of water. I would check the
> flash point of marvel mystery oil, would think it would be quite low.
> I use silicone oil.
> Marvel Mystery oil make up.
> It is composed primarily of petroleum distillates, including mineral *oil* (60–100%),
> mineral spirits (10–30%), tricresyl phosphate (an antiwear and extreme
> pressure additive in lubricants, 0.1–1.0%), ortho-dichlorobenzene (a
> softening and removing agent for carbon-based contamination on metal
> surfaces, 0.1–1.0%), and ...
> It is a class 3 flammible liquid.
> Your 10,000 lumen lights will be fine in water but probably heat up really
> fast out of it.
> I have experimented with them in the kitchen sink and mine hardly warm up
> in water but are untouchable after a couple of minutes out of water.
> The Mc Master Carr lens sounds good.
> Mine were heat and pressure resistant borosilicate lenses.
> Alan
>
>
> On Wednesday, December 30, 2020, 04:06:51 PM GMT+13, Rick Patton via
> Personal_Submersibles <personal_submersibles at psubs.org> wrote:
>
>
> Alan
>
> I don't have facebook but my wife does. not being familiar with the
> format, how would I look up your lights?
> my cobs are 1 13/16" X 1 9/16" and about 1/8" thick. What approximate size
> are yours and how does a flip chip differ from a regular cob? have you had
> any burn out from getting too hot?
> I am using a dielectric oil in my light housings called Marvel Mystery oil
> to get around the pressure differential problem but it has a slight color
> to it so will have to see how the light is effected by that and if it gets
> any worse from being heated. 10,000 lumens is a lot of light so
> hopefully they will still be bright enough. I am using oil compensated
> thrusters as well and I do have small bladders that can expand and contract
> with heat.
> I bought heat treated lenses from Mcmaster Carr but they were about $22
> each and they are glass instead of acrylic.
> Rick
>
>
> On Tue, Dec 29, 2020 at 2:55 PM Alan James via Personal_Submersibles <
> personal_submersibles at psubs.org> wrote:
>
> Hi Rick,
> I posted a couple of pictures of them on the psubs Facebook page. Not sure
> whether you are on there or not.
> The lights are about 7000lm. Leds are usually around 100lms per Watt. They
> are rated a bit more but I am under driving them as they get too hot
> otherwise.
> They are chip on board leds. A technology called "flip chip". I bought
> them off the manufacturer in China.
> Marine anodizing is thicker, 25 microns. You can get more corrosion
> protection with hard anodizing. It affords extra protection against
> galvanic corrosion.
> The buck boost drops or increases the supply voltage to the voltage
> required for the led. In my case I can connect the driver to anything from
> 12V to 60V and it increases/reduces it to the 36V required  by the led. The
> driver should also be CC (constant current) as the resistance of the led
> drops as it heats up & allows a lot more current through.
> I didn't want oil as its messy, & hard to get all the air out. It can also
> discolour with heat. It's used successfully by lots of people. One
> technique with oil filling is to have a hose fitting out the back of the
> light with a pvc tube attached that the wires run down. The tube is
> pre-crimped so that it collapses easy under pressure & equalises the light
> fitting.
> I am using glass lenses because acrylic holds the heat in.
> Alan
>
>
> On Wednesday, December 30, 2020, 10:37:56 AM GMT+13, Rick Patton via
> Personal_Submersibles <personal_submersibles at psubs.org> wrote:
>
>
> Hi Alan
>
> Couple of questions
>
> How many lumens are your lights
> What is the source of the light? COB?
> How does marine anodizing differ from just regular anodizing and why do
> you think that is necessary?
> Is the Buck Buster/LED driver only needed to be able to dim?
> Why did you want to avoid oil?
> Rick
>
> On Tue, Dec 29, 2020 at 10:59 AM Alan James via Personal_Submersibles <
> personal_submersibles at psubs.org> wrote:
>
> Rick,
> I spent a lot of time on my light project, initially looking for & buying
> lights & housings on line, that I could adapt.
> I ended up buying 70W leds & making my own housings. The housings I had
> marine anodized. I had to get an led driver designed & built in China, as I
> wanted dimming. The driver is a constant current step up, step down (buck
> boost) that takes a 12-60V input.
> I had the lenses made up in China; 20 for about $2- each. The units were
> tested to 1000psi. Have used them quite a bit in caves! They get hammered
> in that instance because they don't have the water cooling & can get very
> hot.
> Other people have oil filled spot lights used on off road vehicles
> successfully, but I wanted more of a race car look to my sub & wanted to
> avoid the oil.
> If a housing or light came up that was suitable & easy to adapt I would
> use it.
> But bare in mind that most online lights would need marine anodizing.
> Alan
>
>
> On Wednesday, December 30, 2020, 08:08:07 AM GMT+13, Rick Patton via
> Personal_Submersibles <personal_submersibles at psubs.org> wrote:
>
>
> I built my own aluminum exterior light housing, 6 each, using a cob led
> bulb that was 10,000 lumens, DC 34 volt and about 100 watts. My friend
> found them online and they were about $3.50 each.
>  I fried a number of them due to poor heat sink or driving them too much
> and finally got them dialed in. I asked my friend to buy some more and he
> said that the source in Japan does not sell them any more.
>  I found something similar here in the U.S after hours of searching that
> matched pretty closely to what I had but they were about $38 each. Is
> anyone using something similar as far as lumens goes that has any sources I
> could try or is that price about the best I can do?
>
> Rick
> _______________________________________________
> Personal_Submersibles mailing list
> Personal_Submersibles at psubs.org
> http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
> _______________________________________________
> Personal_Submersibles mailing list
> Personal_Submersibles at psubs.org
> http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
>
> _______________________________________________
> Personal_Submersibles mailing list
> Personal_Submersibles at psubs.org
> http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
> _______________________________________________
> Personal_Submersibles mailing list
> Personal_Submersibles at psubs.org
> http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
>
> _______________________________________________
> Personal_Submersibles mailing list
> Personal_Submersibles at psubs.org
> http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
> _______________________________________________
> Personal_Submersibles mailing list
> Personal_Submersibles at psubs.org
> http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
>
> _______________________________________________
> Personal_Submersibles mailing list
> Personal_Submersibles at psubs.org
> http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
> _______________________________________________
> Personal_Submersibles mailing list
> Personal_Submersibles at psubs.org
> http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
>
> _______________________________________________
> Personal_Submersibles mailing list
> Personal_Submersibles at psubs.org
> http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
> _______________________________________________
> Personal_Submersibles mailing list
> Personal_Submersibles at psubs.org
> http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.whoweb.com/pipermail/personal_submersibles/attachments/20210101/b2cc937b/attachment-0001.html>


More information about the Personal_Submersibles mailing list