[PSUBS-MAILIST] SeaQuestor progress

[Rick Patton via Personal_Submersibles]

Thanks David, quite a set up! glad it worked well for ya. I'll check it out.
Rick

On Sun, May 5, 2019 at 8:49 PM David Colombo via Personal_Submersibles <
personal_submersibles at psubs.org> wrote:

> Hi Rick, here are photos of the hot wire rig I built. Parts are 300w
> computer power supply, use 5v output wire. Two j boxes, one std outlet to
> be wired as 5v. Second j box has variable control. Two std two wire
> extension cords, i used 12ft., 1 inch pvc pipe, sweeps, and caps. 4
> eyebolts with nylock and std nuts. Nicrome wire. I built my large bow to be
> able to cut 36"  x 12" deep foam blocks, the two hand held wands i use 24"
> wire. The hand held rig runs hotter and cuts faster. The large rig cuts 48"
> in about 4 min.  I did not put a bow tightner and so it cuts with slight
> arc as it cuts, nothing that has caused any issues with straightness. For
> straight edges i used two drywall squares which are 48" long, and with a
> couple of 3" screws they are held to the foam,  and i draw the hotwire
> against them. It works pretty slick. All of the foam pieces i have cut have
> been done with these two rigs. Total cost, less than $30. Built in about
> an hour. Have fun.
> David
>
> On Sun, May 5, 2019, 12:19 PM Rick Patton via Personal_Submersibles <
> personal_submersibles at psubs.org> wrote:
>
>> Thanks David.
>> Rick
>>
>> On Sat, May 4, 2019 at 6:14 PM David Colombo via Personal_Submersibles <
>> personal_submersibles at psubs.org> wrote:
>>
>>> Hi Rick, I'll send pictures and notes tomorrow on my rig.
>>> David
>>>
>>> On Sat, May 4, 2019, 8:25 PM Rick Patton via Personal_Submersibles <
>>> personal_submersibles at psubs.org> wrote:
>>>
>>>> Looking good Dave! I have yet to form my styrofoam block but it's my
>>>> next hurdle. I think you explained how you made your hot wire but I can't
>>>> find the thread. Would love to know how you did it or let me know what date
>>>> you sent it and I'll try and find it in the archives. I have a welding
>>>> machine but it may be too much oomph even on it's lowest setting to cut
>>>> without setting the styrofoam on fire.
>>>> Rick
>>>>
>>>> On Fri, May 3, 2019 at 11:09 PM hank pronk via Personal_Submersibles <
>>>> personal_submersibles at psubs.org> wrote:
>>>>
>>>>> Dave, pretty clever using tin foil.
>>>>> Hank
>>>>>
>>>>> On Friday, May 3, 2019, 9:02:41 PM MDT, David Colombo via
>>>>> Personal_Submersibles <personal_submersibles at psubs.org> wrote:
>>>>>
>>>>>
>>>>> Hi Guys, working on the first inner mold form for the ballast tank
>>>>> today. Sliced the foam to 1/4" sheets, and trapazoid shapes to sit over
>>>>> each of the tribs. Then tapped it into place and then spray glued and
>>>>> tinfoil applied to protect the foam. Tomorrow a couple of coats of wax and
>>>>> then the first layer of matt glass. The inner shell will be attached to the
>>>>> exoskeleton to create the ballast tanks. Plan is 4 total, two aft and two
>>>>> adjacent to the rear pilot.  Now that i got the form work dialed in, three
>>>>> more to go.
>>>>>
>>>>> David
>>>>> _______________________________________________
>>>>> Personal_Submersibles mailing list
>>>>> Personal_Submersibles at psubs.org
>>>>> http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
>>>>> _______________________________________________
>>>>> Personal_Submersibles mailing list
>>>>> Personal_Submersibles at psubs.org
>>>>> http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
>>>>>
>>>> _______________________________________________
>>>> Personal_Submersibles mailing list
>>>> Personal_Submersibles at psubs.org
>>>> http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
>>>>
>>> _______________________________________________
>>> Personal_Submersibles mailing list
>>> Personal_Submersibles at psubs.org
>>> http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
>>>
>> _______________________________________________
>> Personal_Submersibles mailing list
>> Personal_Submersibles at psubs.org
>> http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
>>
> _______________________________________________
> Personal_Submersibles mailing list
> Personal_Submersibles at psubs.org
> http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.whoweb.com/pipermail/personal_submersibles/attachments/20190506/5cc107be/attachment.html>