[PSUBS-MAILIST] Foam preperation
Cliff Redus via Personal_Submersibles
personal_submersibles at psubs.org
Thu Jun 27 23:16:58 EDT 2019
This could work. Would need the pressure gauge to confirm that water did not leak out on return to the surface. It is probably easier just to cast a sample and send it to Hank to video at depth with a ruler behind it.
To get a 16 lbf/ft^3 specific volume at one atm, the foam would have to have over 70% air trapped in the foam at the surface. I just can't see how this air in not going to collapse at depth to some degree.
What you need is syntactic foam which was designed for this application. If the foam shrinks during the descent, you are going to have to use your MBT to compensate.
I think you would do better to make a simplified syntactic foam with off the shelf polyester resin plus 3M glass micro-spheres as a filler. Without macorospheres, I think the best specific weight you can expect is 30-40 lbf/ft^3 but at lease you would be assured that this buoyancy was depth independent because the air filled glass microspheres would be keeping the from collapsing.
Best Regards
Cliff
On Thursday, June 27, 2019, 09:32:28 PM CDT, Brian Cox via Personal_Submersibles <personal_submersibles at psubs.org> wrote:
Maybe I could pour the foam into a large diameter pipe of say 5" x 10" long, close the pipe up with a bell fitting , plumb in a high pressure check valve, but before that put in a tee with a ball valve. As the pipe descends water comes in through the check valve as the foam ( allegedly) shrinks in volume. Then, when it is brought up the check valve keeps the pressure at the max depth pressure (600' depth) . When the pipe is at the surface it would still have the pressure of say 300psi. Then you could open the ball valve into a container and measure the amount of seawater that was drawn in . Maybe put a pressure gauge on there too.
Brian
--- personal_submersibles at psubs.org wrote:
From: Brian Cox via Personal_Submersibles <personal_submersibles at psubs.org>
To: "Personal Submersibles General Discussion" <personal_submersibles at psubs.org>
Subject: Re: [PSUBS-MAILIST] Foam preperation
Date: Thu, 27 Jun 2019 18:23:42 -0700
Cliff, There is probably a way I can determine if it shrinks or not at depth. I'm sure some clever person on this list could devise such a way .
Brian
--- personal_submersibles at psubs.org wrote:
From: Cliff Redus via Personal_Submersibles <personal_submersibles at psubs.org>
To: Personal Submersibles General Discussion <personal_submersibles at psubs.org>
Subject: Re: [PSUBS-MAILIST] Foam preperation
Date: Thu, 27 Jun 2019 18:17:45 -0500
Brian this would only be a good test if you had a camera on it with a ruler. I believe it would compress significantly then expand when you took back to surface. Without microspheres and or macro spheres, there is just nothing to keep the entrained air from shrinking . The pressure rating you need is what pressure you can take without any change in volume.
Cliff
Sent from my iPhone
On Jun 27, 2019, at 5:01 PM, Brian Cox via Personal_Submersibles <personal_submersibles at psubs.org> wrote:
I think what I might just do is just go out in my sailboat , off Pt. Magu, and drop a test plug down to 600' , bring it back up and check it out. Need to go out for a sail anyway !
Brian
--- personal_submersibles at psubs.org wrote:
From: Alan via Personal_Submersibles <personal_submersibles at psubs.org>
To: Personal Submersibles General Discussion <personal_submersibles at psubs.org>
Subject: Re: [PSUBS-MAILIST] Foam preperation
Date: Fri, 28 Jun 2019 08:41:55 +1200
Brian,If I had $3million spare I wouldn't spend it on syntactic foam.The danger is that if you were descending you might not know that youwere becoming negatively buoyant until you tried to stop. Then when you tried to counter by filling the ballast tanks with air; because of the compressionof the air at depth this might be a slow process.Bottom line is not to dive the sub in depths that are beyond your maximumdive depth till you are confident the foam isn't compressing.Alan
On 28/06/2019, at 7:41 AM, Brian Cox via Personal_Submersibles <personal_submersibles at psubs.org> wrote:
Alan, I don't have 3 million dollars. In any event I only need it to go to 300 psi, theoretically , I also have about 1000 cu ft of air on board and could easily fill my ballast many times over even if the foam were to shrink. I don't think the foam has an elastic property to it.
Brian
--- personal_submersibles at psubs.org wrote:
From: Alan via Personal_Submersibles <personal_submersibles at psubs.org>
To: Personal Submersibles General Discussion <personal_submersibles at psubs.org>
Subject: Re: [PSUBS-MAILIST] Foam preperation
Date: Fri, 28 Jun 2019 07:33:33 +1200
Brian,as Cliff says it may have a volumetric change under pressure that leavesyou negatively buoyant. I am not sure how you would test this in a pressure chamber.As an example, a soccer ball could take a lot of pressure & look perfectlyfine after a pressure test even though it might have been reduced to a fraction of its original size in the process.I was told that Alvin's syntactic foam & testing process cost $3 million.They put it together in segments after testing each individual segment.It might be perfectly OK though...Alan
On 28/06/2019, at 7:03 AM, Brian Cox via Personal_Submersibles <personal_submersibles at psubs.org> wrote:
I have a pressure gauge guy who does oil industry work that I think has a small chamber where I could test a plug of foam.
Brian
--- personal_submersibles at psubs.org wrote:
From: Brian Cox via Personal_Submersibles <personal_submersibles at psubs.org>
To: "Personal Submersibles General Discussion" <personal_submersibles at psubs.org>
Subject: Re: [PSUBS-MAILIST] Foam preperation
Date: Thu, 27 Jun 2019 11:37:26 -0700
Cliff, It's rated for 580 psi.
Brian
--- personal_submersibles at psubs.org wrote:
From: Cliff Redus via Personal_Submersibles <personal_submersibles at psubs.org>
To: Brian Cox via Personal_Submersibles <personal_submersibles at psubs.org>
Subject: Re: [PSUBS-MAILIST] Foam preperation
Date: Thu, 27 Jun 2019 15:55:01 +0000 (UTC)
Brian, this is not syntactic foam. It's made for marine service but not for deep submergence. It is really for surface buoyancy. I would not use this if you are relying on it for buoyancy at depth. It is the macro-spheres and microspheres in syntactic foam that prevent it compression at depth. I don't think this foam has either.
Best Regards
Cliff
On Thursday, June 27, 2019, 10:45:29 AM CDT, Brian Cox via Personal_Submersibles <personal_submersibles at psubs.org> wrote:
Clifff, Here is the foam, it's the most dense foam , the 16lbs / cu ft
http://www.uscomposites.com/foam.html
suppose to be good to 580 psi
Brian
--- personal_submersibles at psubs.org wrote:
From: Cliff Redus via Personal_Submersibles <personal_submersibles at psubs.org>
To: Brian Cox via Personal_Submersibles <personal_submersibles at psubs.org>
Subject: Re: [PSUBS-MAILIST] Foam preperation
Date: Thu, 27 Jun 2019 14:29:12 +0000 (UTC)
Brian, I have been tied up and have not had a chance to follow this thread but I wanted to make sure you understand that unless this pour-able 2 part foam has a filler like 3-M's glass micro-spheres or some kind of incompressible macrosphere, then while the foam may appear rigid, it would compress when subjected to deep water and thus your buoyancy would be reduced. I don't think this is a replacement for syntactic foam if that is what you are doing. Can you send a link to the foam you are using?
Best Regards
On Wednesday, June 26, 2019, 10:30:48 PM CDT, Brian Cox via Personal_Submersibles <personal_submersibles at psubs.org> wrote:
Hi everybody, I poured a small test piece of that 16 lb foam, man that stuff gets as hard as a rock ! very dense , and very light. This pouring of the foam is not going to be as straight forward as I thought, The barrier to contain the foam is working out good, I'm just using wood and thin 1/8" luan , then I'm covering that with 4 mil flexible plastic ( heavy garbage type bag) so the foam won't stick to it. But I'm worried that any little gaps I have and the liquid foam might run out the bottom of those areas before it starts foaming, so I'm cramming big blankets ( cheap moving blankets from harbor freight) in tight to contain any foam. That way I can get the cavity that I'm trying to fill completely maxed out. Waiting for an 80 + degree day .
Brian
--- personal_submersibles at psubs.org wrote:
From: Brian Cox via Personal_Submersibles <personal_submersibles at psubs.org>
To: "Personal Submersibles General Discussion" <personal_submersibles at psubs.org>
Subject: Re: [PSUBS-MAILIST] Foam preperation
Date: Mon, 24 Jun 2019 16:12:46 -0700
My first batch of foam cam today ! yay ! two five gallon pails, A and B, should be interesting !
Brian
--- personal_submersibles at psubs.org wrote:
From: hank pronk via Personal_Submersibles <personal_submersibles at psubs.org>
To: Brian Cox via Personal_Submersibles <personal_submersibles at psubs.org>
Subject: Re: [PSUBS-MAILIST] Foam preperation
Date: Fri, 21 Jun 2019 17:47:56 +0000 (UTC)
Brian,Did you find foam to fill the void?Hank
On Thursday, June 20, 2019, 8:30:55 PM MDT, Brian Cox via Personal_Submersibles <personal_submersibles at psubs.org> wrote:
Kind of unnerving drilling holes in my boat !
_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
_______________________________________________Personal_Submersibles mailing listPersonal_Submersibles at psubs.orghttp://www.psubs.org/mailman/listinfo.cgi/personal_submersibles_______________________________________________Personal_Submersibles mailing listPersonal_Submersibles at psubs.orghttp://www.psubs.org/mailman/listinfo.cgi/personal_submersibles_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
_______________________________________________Personal_Submersibles mailing listPersonal_Submersibles at psubs.orghttp://www.psubs.org/mailman/listinfo.cgi/personal_submersibles_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
_______________________________________________Personal_Submersibles mailing listPersonal_Submersibles at psubs.orghttp://www.psubs.org/mailman/listinfo.cgi/personal_submersibles_______________________________________________Personal_Submersibles mailing listPersonal_Submersibles at psubs.orghttp://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
_______________________________________________Personal_Submersibles mailing listPersonal_Submersibles at psubs.orghttp://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
_______________________________________________Personal_Submersibles mailing listPersonal_Submersibles at psubs.orghttp://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
_______________________________________________Personal_Submersibles mailing listPersonal_Submersibles at psubs.orghttp://www.psubs.org/mailman/listinfo.cgi/personal_submersibles_______________________________________________Personal_Submersibles mailing listPersonal_Submersibles at psubs.orghttp://www.psubs.org/mailman/listinfo.cgi/personal_submersibles_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.whoweb.com/pipermail/personal_submersibles/attachments/20190628/eda638a0/attachment-0001.html>
More information about the Personal_Submersibles
mailing list