[PSUBS-MAILIST] Optical Oxygen Sensors

Tue Aug 20 22:01:21 EDT 2019

 Alan,I like your plan to feed O2 as needed, like a bellows add.  BTW I have a new O2 solenoid valve from an Inspiration II re-breather you can have.Hank
    On Tuesday, August 20, 2019, 7:31:27 PM MDT, Alan via Personal_Submersibles <personal_submersibles at psubs.org> wrote:  

 Thanks David,I know Cliff was getting some good results re the range he was keepingO2 at? And that would be more difficult than in a bigger sub.I am pretty well settled on what I am doing now, which is going with thestandard sensor, as apposed to the optical. The standard galvanic sensor I canget anywhere but the optical I have to import from Scotland.Also it seems simpler for me to implement with its voltage output than the dataoutput of the optical sensor. The optical sensor also requires a power supply.Alan

On 21/08/2019, at 11:25 AM, David Colombo via Personal_Submersibles <personal_submersibles at psubs.org> wrote:

Hi Alan, having had the second seat in the Gamma while at Flathead for the expedition,  I monitored and logged the O2 readings through out the dives. Start at hatch closure, upon reaching depth(up to 200ft+), at mid mark of the planned dive duratation and again upon accent.The variation was minor throught the dive.David
On Tue, Aug 20, 2019, 3:23 PM hank pronk via Personal_Submersibles <personal_submersibles at psubs.org> wrote:

 Alan,I can't speak to O2 level recovery with the hatch open after a dive, but I can say that working in the sub I have the CO2 metre on all the time if the sub is powered up.  The CO2 level does not come down in a noticeable rate, in fact, just working in the sub with the hatch open, levels are 2500 and up.  I would say in Gamma, the O2 level would not recover quickly.  That is why I calibrate my O2 meter outside the sub.Hank
    On Tuesday, August 20, 2019, 1:45:18 PM MDT, Alan via Personal_Submersibles <personal_submersibles at psubs.org> wrote:  

 Jon, Hank.It would be good if someone (Hank) could measure O2 levels in the sub& outside air to see how long it takes for them to reach an equilibrium.You may find that leaving the hatch open for a minute is all it takes.I am trying to build a smaller sub than the R300, so opening the hatch shouldbe enough to equalise the O2 levels. Also with going smaller any environmentalchanges happen faster, hence the need for 3 X O2 sensors.Alan
On 21/08/2019, at 12:24 AM, Jon Wallace via Personal_Submersibles <personal_submersibles at psubs.org> wrote:

Alan, almost all the rebreather galvanic sensors have quick disconnect adapters.  I think I'm going to deal with calibration by fabricating a small handheld analyzer that I can connect the same sensor to outside atmospheric air and then reconnect back to the main processor in the vessel.  The more I think of it, I will probably just make this handheld O2 sensor a separate physical module that can run on it's own power and "plug-in" to the main processor.  For example, something like the "el cheapo" from oxycheq that could connect to and direct it's output to the main processor.  This approach would work for the CO2 sensor as well.
Jon

_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles

_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
  _______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles

_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles

_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.whoweb.com/pipermail/personal_submersibles/attachments/20190821/8a4262ab/attachment-0001.html>